Technical Vault: Ansell HyFlex® 11-751 Cut Resistant Industrial Gloves

The Ansell HyFlex® 11-751 is a dirt-masking A4 / EN ISO C cut-resistant glove engineered for workers who need higher everyday cut protection, abrasion resistance, puncture resistance, touchscreen compatibility, polyurethane grip, and long visible wear life. It combines INTERCEPT™ Cut Resistance Technology, a polyurethane palm coating, a 10-gauge nylon / HPPE / fiberglass / spandex liner, and a knitwrist cuff.

This Technical Vault summarizes the verified construction, standards, material profile, cut and abrasion performance, sizing guidance, application guidance, inspection points, storage notes, and use limitations for the HyFlex® 11-751.

Vault summary: Dirt-masking A4 / EN ISO C cut glove with INTERCEPT™ Cut Resistance Technology, polyurethane palm coating, 10-gauge nylon / HPPE / fiberglass / spandex liner, ANSI abrasion level 6, ANSI puncture level 4, EN 388 4X43C, touchscreen compatibility, Category II classification, OEKO-TEX® 1408033, REACH compliance, sizes 5–11, and 12 pairs/bag, 12 bags/carton packaging.

Proper glove sizing helps improve comfort, dexterity, grip control, and protection. To measure your glove size, wrap a tape measure around the widest part of your dominant hand, just below the knuckles, excluding the thumb.

Fit note: This product is listed in numeric sizes 5, 6, 7, 8, 9, 10, and 11. Size 5 is smaller than the standard SOS Ansell chart shown above; verify fit using Ansell product sizing or site-specific fitting procedures. A properly sized A4 cut glove should feel secure without restricting hand movement.

Standards note: EN 388 4X43C describes mechanical performance. The “X” in the circular blade cut position means the ISO cut letter should be used for cut classification. For this glove, the reported ISO cut letter is C.

Ansell lists environmental attributes for the HyFlex 11-751 under its Ansell Earth profile. These attributes relate to manufacturing and packaging rather than glove hazard performance.

• Manufactured in a facility certified by Intertek for diverting more than 99% of waste from landfill
• Manufactured in a facility with an accredited Environmental Management System
• Plastic-free packaging
• Recyclable packaging
• Shipper case includes a minimum of 80% recycled material
• Primary packaging redesigned to contain 70% less material versus previous packaging
• Paperband made of responsibly sourced raw material
• Shipper case sizes optimized for efficient shipping

• General maintenance
• Hardware assembly
• Machining
• Stamping
• Cutting support tasks
• Raw material handling
• Seat and frame build
• Machinery and equipment work
• Automotive production and maintenance
• Touchscreen-enabled inspection, scanning, and workstation tasks
• Higher everyday cut-risk tasks requiring ANSI A4 / EN ISO C protection

• Chemical immersion or validated chemical breakthrough protection
• Liquidproof barrier protection
• High heat, open flame, molten metal splash, or thermal protection applications
• Moving blade hazards or powered cutting tools
• Needle, hypodermic, or ultra-fine puncture hazards
• Electrical protection or antistatic-controlled applications requiring validated antistatic PPE
• Silicone-sensitive painting, coating, or contamination-control processes unless validated by the site
• Heavy cut-force applications requiring a higher ANSI or ISO cut rating
• Oil-saturated handling requiring oil-repellent or liquid-repellent glove technology
• Sterile cleanroom processing unless separately validated for the controlled environment

Select the HyFlex 11-751 when the job requires a glove that prioritizes ANSI A4 cut resistance, EN ISO C cut classification, very high abrasion resistance, strong general mechanical puncture resistance, dirt-masking appearance, touchscreen compatibility, and polyurethane palm grip. It is best matched to higher everyday cut-risk maintenance, assembly, machining, stamping, cutting support, raw material handling, and automotive frame build tasks.

• Inspect the polyurethane palm coating for cuts, punctures, cracks, peeling, worn-through areas, or loss of grip.
• Check fingertips, thumb crotch, palm, and other high-contact zones for coating separation or abrasion damage.
• Confirm the 10-gauge liner is intact and that nylon, HPPE, fiberglass, or spandex fibers are not exposed through excessive wear.
• Check that touchscreen function remains acceptable for the task if device use is required.
• Check that the knitwrist cuff is not stretched out, torn, contaminated, or loose.
• Do not use gloves contaminated with unknown chemicals, heavy oils, greases, or incompatible substances.
• Replace gloves when coating integrity, grip performance, cut protection, touchscreen performance, fit, or protective function is visibly compromised.

• Store gloves in a clean, dry location away from excessive heat, direct sunlight, ozone, ignition sources, and sharp objects.
• Keep gloves away from incompatible chemicals unless separately evaluated for that exposure.
• Avoid crushing, folding, or contaminating the polyurethane palm coating during storage.
• Keep touchscreen contact areas clean enough to support device use where required.
• Use clean, dry hands when donning gloves to maintain liner comfort and reduce contamination transfer.
• Follow site PPE procedures for reuse, inspection, laundering, contamination control, and disposal.

The HyFlex 11-751 is an industrial cut-resistant glove, not a sterile cleanroom glove. For controlled environments, evaluate the glove against the site’s particulate, extractable, linting, contamination, packaging, laundering, polyurethane coating, silicone status, antistatic requirements, touchscreen use, and gowning requirements before approval. Use cleanroom-qualified gloves when the process requires validated low-particle, sterile, or cleanroom-specific hand protection.

What is the cut level of the HyFlex 11-751?
The glove is rated ANSI Cut Level A4 and carries an EN ISO cut level C classification under EN 388 4X43C.

What makes the HyFlex 11-751 suitable for demanding everyday tasks?
It combines A4 / EN ISO C cut protection, ANSI abrasion level 6, ANSI puncture level 4, polyurethane palm grip, and a dirt-masking black design.

Is this glove touchscreen compatible?
Yes. Ansell lists the HyFlex 11-751 as touchscreen compatible, allowing device use without glove removal.

What is the coating material?
The glove uses a polyurethane palm coating, supporting tactile grip and abrasion resistance.

What is the liner material?
Ansell lists the liner as nylon, HPPE, fiberglass, and spandex in a 10-gauge knitted construction.

Is this glove silicone free or antistatic?
No. Ansell lists the HyFlex 11-751 as not silicone free and not antistatic.

The HyFlex 11-751 is designed for A4 / EN ISO C cut-resistant mechanical hand protection. It is not intended for chemical immersion, validated chemical breakthrough protection, liquidproof barrier protection, electrical protection, thermal protection, flame exposure, molten metal splash, moving blade hazards, cut hazards beyond its A4 / EN ISO C rating, antistatic-controlled applications, silicone-sensitive processes, or needle puncture protection. Final glove selection should be based on documented hazard assessment, edge sharpness, contact force, abrasion exposure, puncture exposure, grip requirements, touchscreen requirements, silicone-control requirements, coating condition, glove fit, and replacement frequency.

Technical insight: The HyFlex 11-751 is strongest where A4 cut protection, high abrasion resistance, puncture resistance, dirt masking, and touchscreen compatibility must work together; for chemical, liquid, heat, impact, antistatic, silicone-free, sterile, or cleanroom-specific needs, select a glove designed for that specific hazard profile.

Product page updated: Mar. 2026 (SOS Technical Staff)

© 2026 SOSCleanroom.com